Jump to content


TRK23DOz vs TRK23DOzx


  • Please log in to reply
2 replies to this topic

#1 Luis Babboni

Luis Babboni

    Regular Member

  • Member
  • PipPipPipPipPip
  • 57 posts

Posted 21 April 2011 - 07:28 PM

I have troubles using the TRK23DOzx.
I cant see an outfield object if I put an infield one!  :blink:
But I was reading the tutorial for the TRKDOw.... so later I find the  tutorial for the TRK23DOz... but still have the same problem... and now, I see that Im using the TRK23DOzx... but I cant find its toturial.  :(

Below differents ways I tried, never can see both objetcs at the same time.
Maran is an outside object and banco01 an infield one.

Trackside Objects
obj 3 1713.34 20.02 0.095 230.0 0.0 0.0 1.0 maran
obj 3 1755.7450 7.4874 -0.0160 0.0 0.0 0.0 1.0 banco01


Trackside Objects
Outfield Object
obj 3 1713.34 20.02 0.095 230.0 0.0 0.0 1.0 maran
Infield Object
obj 3 1755.7450 7.4874 -0.0160 0.0 0.0 0.0 1.0 banco01


obj 3 1713.34 20.02 0.095 230.0 0.0 0.0 1.0 maran
obj 3 1755.7450 7.4874 -0.0160 0.0 0.0 0.0 1.0 banco01

Edited by Luis Babboni, 21 April 2011 - 07:39 PM.


#2 ginetto

ginetto

    Master Tracker

  • Administrators
  • PipPipPipPipPipPipPipPipPipPipPipPip
  • 10,660 posts
  • Gender:Male
  • Location:Lombardia ITALIA

Posted 22 April 2011 - 09:27 AM

With that command lines, you are placing normal track side objects that lays inside the track.3do
Infield or outfield objects are basically objects that are outside the limits of the track.3do and are:
on the left ( iref) and
on the right ( oref)

Ther doZ (doZx is the same, only difference is that you can use it for long tracks too) command to address these in the TSO file  is:

iobj 3 1713.34 20.02 0 230 0 0 1 maran
oref 12 24
  iobj 3 1755.74 7.5 0 0 0 0 1 banco01
iref 20 25

see that at the beginning of the line is:
iobj (means infield object)
NOT obj

after the main line you need to apply a second line that makes the object visible in a frame of sections; you can give a oref line followed by a iref line too but I found out that in most of the cases the result is that clipping shows up.

for maran, in the example is :
on the right ( oref it meant outside - correct if the track is counterclockwise :P ) between sections 12 and 24

for banco01 is:
on the left  ( iref ; it meant inside) between sec 20 and 25

The lines that you write that don't start with:
obj   = normal TSO object
iobj = infield object
oref = right side reference for a iobj
iref = left side reference for a iobj

are considered as comment and not taken in consideration when you compile ;)

Edited by Ginetto, 22 April 2011 - 09:36 AM.

Done these tracks and working on others.


#3 Luis Babboni

Luis Babboni

    Regular Member

  • Member
  • PipPipPipPipPip
  • 57 posts

Posted 23 April 2011 - 12:25 PM

Working!!